Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
45 Cards in this Set
- Front
- Back
|
THE FLYWHEEL OF AN ENGINE AFFECTS THE OPERATION OF THE ENGINE BY WHAT MEANS? |
BY SMOOTHING OUT THE POWER IMPULSES |
|
|
WHICH OF THE BASIC PARTS ARE INCLUDED IN THE 1-CYLINDER ENGINE? |
CYLINDER, PISTON, PISTON PIN, CONNECTING ROD, AND CRANKSHAFT |
|
|
AN INTERAL COMBUSTION ENGINE IS A MACHINE THAT PERFORMS WHAT ACTIONS? |
IT CONVERTS HEAT ENERGY TO MECHANICAL ENERGY |
|
|
WHEN A TIRE/WHEEL ASSEMBLY EXPLODES VIOLENTLY DURING INITIAL INFLATION, WHAT FACTORS ARE NORMALLY THE CAUSE? |
MATERIAL DEFECTS AND IMPROPER ASSEMBLY |
|
|
WHEN INSTALLING A DEMOUNTABLE FLANGE ONTO THE RIM BASE, THE OPENING BETWEEN THE FLANGE ENDS SHOULD BE WITHING WHAT RANGE OF MEASUREMENT? |
3/32 TO 5/16 IN. |
|
|
WHAT TYPE OF TIRE HAS CORDS THAT CROSS THE TIRE AT ANGLES OF 30-40 DEGREES? |
BIAS PLY |
|
|
THE AMOUNT OF FUEL NEEDED BY THE ENGINE IS DETERMINED BY WHAT COMPONENT? |
THE METERING VALVE |
|
|
WHAT FILTER IS DESIGNED WITH THE GREATEST FILTERING QUALITY? |
FABRIC |
|
|
WHEN A DIESEL ENGINE USES TWO FUEL FILTERS, THE PRIMARY FILTER WILL BE THE FILTER BETWEEN WHAT COMPONENTS? |
SUPPLY TANK AND THE FUEL SUPPLY PUMP |
|
|
WHY IS THE DRY-TYPE AIR CLEANER PREFERABLE TO WET-TYPE? |
IT IS MORE EFFECIENT |
|
|
WHAT CONDITIONS ARE AN INDICATION OF A CLOGGED MUFFLER? |
1. ENGINE NOT DELIVERING MAX. POWER 2. DIFFICULT STARTING 3. ENGINE OPERATING AT HIGHER THAN NORMAL TEMPERATURE |
|
|
WHAT COMPONENT VARIES THE AMOUNT OF FUEL-AIR MIXTURE THAT ENTERS THE INTAKE MANIFOLD? |
THE AUTOMATIC CHOKE |
|
|
WHAT COMPONENT MAINTAINS THE PROPER PRESSURE IN THE LINE BETWEEN THE FUEL PUMP AND THE CARBURETOR? |
THE FUEL PUMP |
|
|
WHEN A FUEL FAILS TO EVAPORATE READILY IN A COLD CLIMATE, WHAT CONDITIONS WILL RESULT? |
1. HARD STARTING 2. LOSS OF POWER 3. INCREASED FUEL CONSUMPTION |
|
|
WHAT IS AN ADVANTAGE OF THE QUICK ENGINE CHANGE (QEC) CONCEPT? |
1. PREVENTS DOWNTIME 2. ELIMINATES NEED FOR ENGINE OVERHAUL 3. INCREASES NUMBER OF INTERCHANGEABLE PARTS AVAILABLE |
|
|
A BEARINGS ABILITY FO WITHSTAND BEING EATEN AWAY BY THE BYPRODUCTS OF COMBUSTION IS REFERRED TO BY WHAT NAME? |
CORROSION RESISTANCE |
|
|
A BEARINGS ABILITY TO WITHSTAND REPEATED STRESSES WITHOUT FAILING IS REFERRED TO BY WHAT NAME? |
FATIGUE RESISTANCE |
|
|
A BEARINGS ABILITY TO RESIST WEAR IS REFERRED TO BY WHAT TERM? |
WEAR RATE |
|
|
WHAT HAPPENS AS OIL CLEARANCE IN BEARINGS BECOMES GREATER? |
OIL FLOWS MORE QUICKLY THROUGH THE BEARINGS |
|
|
OIL MOVES ACROSS THE FACE OF A BEARING IN ORDER TO ACCOMPLISH WHAT ACTIONS? |
1. COOL THE BEARING 2. LUBRICATE THE BEARING 3. REMOVE DIRT FROM THE BEARING |
|
|
THE BACK OF A TYPICAL BEARING HALF IS CONSTRUCTED OF WHAT TYPE OF MATERIAL? |
STEEL OR BRONZE |
|
|
WHAT COMPONENT LIMITS THE OPERATING RPM OF AN ALTERNATOR? |
THE BEARINGS |
|
|
WHAT PARTS ARE COMMON TO BOTH ALTERNATORS AND DC GENERATORS? |
ROTOR, STATOR, RECTIFIER |
|
|
THE COMMUTATOR IN A DC GENERATOR IS CONSTRUCTED OF WHAT MATERIAL? |
IRON |
|
|
THE MO SHALL DESIGNATE IS WRITING VIA THE MMP THE ____ AS THE TOOL CONTROL PROGRAM MANAGER? |
MCO (MATERIAL CONTROL OFFICER) |
|
|
WHAT ARE THE SIX PROGRAMS MANAGED BY QA? |
NAMDRP, CTPL, SE MISUSE & ABUSE, AVGFE, MAINTENANCE SAFETY, QA AUDIT |
|
|
THE A/S32A-31A IS SPECIALLY EQUIPPED TO CARRY WHAT TYPE OF EQUIPMENT? |
A GAS TURBINE COMPRESSOR |
|
|
WHAT TYPE OF FUEL ATOMIZER IS USED ON THE GAS TURBINE ENGINES FOUND IN SUPPORT EQUIPMENT? |
DUAL ORIFICE |
|
|
WHAT SECTION OF A TURBINE IS DESIGNED TO INCREASE THE PRESSURE OF THE AIR AND DISCHARGE IT TO THE COMBUSTION CHAMBER? |
THE COMPRESSOR SECTION |
|
|
WHAT ARE THE PRINCIPAL PARTS OF THE STEERING GEAR UNIT? |
THE WORM AND SECTOR GEAR |
|
|
THE TMU-70/M IS A COMPLETELY SELF-CONTAINED UNIT. WHAT ARE THE THREE MAJOR COMPONENTS? |
1. 50 GAL. DEWAR TANK 2. 15 L TRANSFER TANK 3. LOW-LOSS, CLOSED LOOP SYSTEM TRANSFER LINES |
|
|
WHAT TYPE OF PUMP IS USED ON THE B-2 MAINTENANCE PLATFORM? |
DOUBLE-ACTION PUMP |
|
|
THE ___ MANAGE THE SUPPORT EQUIPMENT TRAINING AND LICENSING PROGRAM FOR I-LEVEL? |
SUPPORT EQUIPMENT DIVISION OFFICER |
|
|
WHAT REPORT IS USED TO MONITOR TECHNICAL DIRECTIVES THAT HAVE NOT BEEN COMPLIED WITH? |
MDR4-1 |
|
|
WHAT REPORT TRACKS MONTHLY MAINTENANCE PRODUCTION? |
MDR-2 |
|
|
SUPPORT EQUIPMENT MISUSE AND ABUSE ARE DOCUMENTED ON WHAT FORM? |
OPNAV 4790/108 |
|
|
WHAT IS A 4790/60? |
VIDS MAF |
|
|
WHAT FORM IS USED TO DESIGNATE QAR'S AND CDI'S? |
OPNAV 4790/12 |
|
|
CORROSION APPEARANCE ON ALUMINUM ALLOY? |
WHITE TO GRAY POWDER |
|
|
CORROSION APPEARANCE ON LOW ALLOY STEEL? |
REDDISH-BROWN OXIDE (RUST) |
|
|
WHAT IS THE FUNCTION OF A CHECK VALVE? |
TO ALLOW FLUID TO FLOW IN ONE DIRECTION ONLY |
|
|
WHAT IS THE FUNCION OF A BYPASS VALVE? |
WHEN PRESSURE ON THE INLET SIDE EXCEEDS PRESSURE ON OUTLET SIDE, THE VALVE WILL OPEN |
|
|
WHAT ARE THE MAJOR PARTS OF A HYDRAULIC SYSTEM? |
PUMPS ACTUATORS RESEVOIR TUBING SELECTOR VALVE |
|
|
WHAT IS THE FUNCTION AND PURPOSE OF AN ACCUMULATOR? |
TO HOLD FLUID PRESSURE FOR NORMAL AND EMERGENCY USAGE |
|
|
WHAT IS THE PURPOSE OF A HYDRAULIC PUMP? |
TO ALLOW FOR A FLOW OF FLUID IN A HYDRAULIC SYSTEM |
