Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
49 Cards in this Set
- Front
- Back
- 3rd side (hint)
How many chains are in each lot? |
10 |
|
|
Are there other authorized tiedowns aboard ships? |
No |
|
|
What's the name for the tiedown chain assembly? |
TD-1B |
|
|
What is the weight of the TD-1B? |
Approximately 10.5lbs |
|
|
What is the P/N for the 14ft chain? |
1540AS100-2 |
|
|
Is color coding encouraged for the tiedowns? |
Yes |
|
|
Incorrect installation of the chain into the locking mechanism reduces the breaking strength to ______ |
Approximately 6,000lbs |
|
|
What type of corrosion involves only the metal surface and is generally seen as dulling or etching of the surface? |
Uniform Surface Corrosion |
|
|
What type of corrosion often occurs between fraying surfaces? |
Crevice Corrosion |
|
|
What are the 3 types of crevice corrosion? |
Metal-Ion Concentration, Oxygen Concentration and Active-Passive Cells |
|
|
How long do you have to incorporate RACs and IRACs into the affected Technical Manuals (paper copy)? |
2 business days of |
|
|
What does RACs stand for? |
Rapid Action Changes |
|
|
What does ELMS stand for? |
Enhanced Library Management Systems |
|
|
If the new paper version of the manuals isn't received within 60 days of being posted on the NATEC website the prior version of the paper manual must be considered out of date. What is allowed to be used in that case? |
The new version posted on NATEC |
|
|
Will indicates? |
Futurity and never indicates any degree of requirements for applications of a procedure |
|
|
During the 60 day delivery period the manual will not be available for what? |
Requisitioning and ELMS Audit Library record will have a yellow D icon |
|
|
What does NATEC stand for? |
Naval Air Technical Data and Engineering Service Center |
|
|
Individual 4790/51 forms will be prepared for what restraints? |
Engine run up restraint, holdback adapter or restraint fitting |
|
|
Where do you insert a copy of the IRAC? |
Right behind the title page |
|
|
What type of corrosion is a result from an attack on the grain boundaries of a metal? |
Intergranular Corrosion |
|
|
What determines the rate of galvanic corrosion? |
If the anode is smaller than the cathode then it will be fast |
|
|
What type of corrosion is the most common on AL and MN alloys and noticeable as a white or grey powdery deposits? |
Putting Corrosion |
|
|
What type of corrosion results from a constant tensile stress and corrosion of a metal? |
Stress Corrosion |
|
|
Should means |
Procedure is recommended |
|
|
For double column material where do you mark the margin? |
Mark the center margin (inner paragraph) outer margin (outer paragraph) |
|
|
Enter the IRAC number in ___ in the ____ |
Margin, Pencil |
|
|
What is the range of pressure for SE Medium pressure? |
80-130PSI |
|
|
What is the non preferred hook installation? |
Hook pointed down |
|
|
How far should deflated tire flag pin stick out past the open end of the valve stem? |
1/4 inch |
|
|
What is the minimum length required for a deflected tire flag pin? |
3/4 inch |
|
|
What pressure should the tire be deflated to after successful completion? |
50% of service pressure or 15PSI, 100PSI for aircraft tires |
|
|
You should install single wheel of the demountable flange facing what direction? |
Outboard |
|
|
What type of bolts should be used to put together split rim assemblies? |
Grade 5 or stronger fine thread |
|
|
What angle do the 3 plies of the body cords run at on radical tires? |
Right Angles (90 degrees) |
|
|
At what angle do the cords cross the tires on bias belted tires? |
25 degrees |
|
|
How should you loosen tie-bolts to preclude wheel rim damage? |
Crisscross pattern |
|
|
On dual wheel assemblies, you should mount the inner wheel facing what direction? |
Demountable flange facing outboard and the outer wheel flange facing inboard |
|
|
What type of corrosion is identified as severe Intergranular corrosion, blistering, exfoliation, scaling or flaking with a pitting depth deeper than 10 mils? |
Severe corrosion |
Why type od |
|
How is steering accomplished at the front wheels on the A/S32A-45? |
Hydraulic powered steering box and sealed ball joint linkage |
|
|
What is the turning radius of the tractor? |
160 inches right hand turn and 155 inches left hand turn |
|
|
Fault codes associated with 629 are what? |
Engine Control Module (ECM) |
|
|
What are the 2 visual Indications? |
Amber LED (warning) and Red LED (derate/shutdown) |
|
|
When you are shopping the SFC what must you change it back over to if you have been using 220 VAC? |
440 VAC |
|
|
What is the towing capacity of the A/S32A-45? |
80,000 lbs |
|
|
What type of engine is in the A/S32-45? |
Deutz Diesel Turbo Charged |
|
|
What type of drive shaft is on the A/S32A-45? |
Automotive type shaft with double universal joints and spline coupling |
|
|
Fault codes associated with 110 are what? |
Engine Coolant Temperature Related |
|
|
After all active codes are displayed what will be displayed on the transmission display unit? |
2 dashes (--) |
|
|
Fault codes associated with 111 are? |
Coolant level related? |
|