Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
67 Cards in this Set
- Front
- Back
Which router connection can be used for disk-in-access to the router CLI management purposes and does not usually pass normal network traffic? |
AUX |
|
Which type of memory stores startup configuration file for the Cisco device? |
NVRAM |
|
Which of the following best describes the cable that is used to connect a laptop to the Console port on a Cisco router? |
rollover |
|
Which two of the following statements are true about a switch? A: It is a repeater B: It is a data link layer device C: It will forward the frame out all ports when it receives a broadcast from a host D: It reads the destination MAC address to forward traffic out the appropriate port. E: It acts as an amplifier |
It is a data link layer device
It reads the destination MAC address to forward traffic out the appropriate port |
|
Which windows-based text editor is preferred when working with a simply text document such as a Cisco configuration. |
Microsoft Notepad |
|
What does Cisco use for Return Material Authorization (RMA) tracking of the field-replaceable parts? |
RMA number |
|
Which type of memory is necessary for a router to boot? |
DRAM |
|
What does the CD LED indicate on the voice WAN interface card? |
A carrier has been detected |
|
At the interface configuration , which command returns you to the main configuration prompt? |
exit |
|
Which two pieces of information does the show ip interface brief command display? |
Interface status
Layer 3 address |
|
Which two command are used to set the configuration register value? |
Router (config) #config-register 0x2102
rommon>confreg 0x21002 |
|
Which command send an echo request packet to the largest host and then waits for an echo response message? |
ping |
|
You are performing a password recovery on a Cisco fixed Catalyst switch? List by steps
|
Step 1 Power on Step 2 Mode button Step 3 flash_init Step 4 load_helper |
|
Which two pieces of information can be determined about a neighbor device from CLI command show cdp neighbor? |
device ID
platform |
|
Which two of the following are true?
A. Telnet is preferred over SSH for security reasons. B. SSH is a protocol that provides a secure remote access connection to network devices C. When using Hyperterminal to communicate over TCP/IP network the SSH protocol is used. D. A Telnet network management connection is dropped when a router reboots E. Telnet is a protocol that provides a secure remote access connection to network devices. |
1) SSH is a protocol that provides a secure remote access connection to network devices
2) A telnet network management connection is dropped when a router reboot. |
|
Which IOS layer does the server use to keep track of which application communications in which conversation? |
Session |
|
On which three operating system does the Hyperterminal not come pre-installed |
Windows Vista
Mac OSX
Windows 7
|
|
Match the prompt with operation mode |
Router (boot)# Boot Mode Router(config -if)# Interface Mode Router(config)# Global Config Mode Router# Privileged EXEC Mode Rommon> ROM Monitor Mode Router> User EXEC Mode |
|
Which command can be used to identify the serial number of a Cisco router? |
Show version |
|
Which two of the following are features of NVRAM on a Cisco device? A) Stores startup configuration B) Stores running configuration C) Stores routing tables D) Stores decompressed IOS software image E) Erased when device is rebooted F) Not erased when deivce is rebooted |
Stores startup configuration
Not erased when device is rebooted |
|
Which type of memory is used to permanently store the Cisco IOS software |
Flash |
|
Which type of cable is used on the ATM card? |
Coaxial |
|
Which command displays the configuration register setting? |
show version |
|
Which two of the following statements are true?
A) Because FTP usually requires authentication, a Cisco router must be configured with the appropriate username and password. B) FTP uses UDP as its transport protocol C) The copy running-config ftp command is used to copy configuration file from an FTP server to the running configuration. D) A router can act as an FTP server E) FTP can be used to load Cisco IOS software to router in ROMMON mode |
1) Because FTP usually requires authentication, a Cisco router must be configured with the appropriate username and password.
2) A router can act as an FTP server |
|
Which three of the following statements are true about a router? (chose three)
A) It forward broadcast frames B) it interconnects multiple network together C) it chooses the best route for your data to travel D) It manages and analyzes a company's database. E) it devices a network into separate broadcast domains |
1) it interconnects multiple network together
2) it chooses the best route for your data to travel
3) it devices a network into separate broadcast domains |
|
What are two ways to open Microsoft Notepad on a windows-based computer? (Choose two)
A) Start > Run Enter Notepad and click OK B) Start > Control Panel > Notepad C) Start > all programs > Notepad D) Start > All Programs > Accessories > Notepad E) Start > All Programs > Microsoft Office > Notepad |
1) Start > Run Enter Notepad and click OK
2) Start > All Programs > Accessories > Notepad |
|
What are tow possible causes if an Ethernet interface is up and the line protocol is down? (Chose two) A) The Ethernet cable might not be attached properly B) There is a speed or duplex mismatch with the remote device C) The Ethernet interface has been manually disabled. D) There is a Layer 2 mismatch in the encapsulation type E) Keepaliver are not being received by the local device |
1) There is a Layer 2 mismatch in the encapsulation type
2) Keepaliver are not being received by the local device |
|
A null modem cable uses which adapter type? |
RS-232 |
|
Which of the following is a DTE device? |
router |
|
Which two of the following CLI operating modes, by default, allow you to copy Cisco IOS image to flash memory from TFTP server? (choose two)
A) User EXEC B) Privileged EXEC C) ROMMON D) Global configuration |
1) Privileged EXEC
2) ROMMON |
|
What are two ways to open a command prompt session on a Windows-based computer? (Chose two)
A) Click Start > Control Panel > Command prompt B) Click Start > All programs > Accessories > Command Prompt C) Click Start > All Programs > Command Prompt D) Click Start > Run Enter cmd and click OK E) Click Start > All Programs > Accessories > Communications > Command Prompt |
1) Click Start > All programs > Accessories > Command Prompt
2) Click Start > Run Enter cmd and click OK |
|
Which of the following best describes the port on a laptop that is used to connection to an Ethernet port on a Cisco Switch? |
RJ-45 |
|
Of which cable type this as example? |
RJ-45 crossover |
|
While performing password recovery on a Cisco device, the configuration register should be which value in order to bypass loading the startup configuration? |
0x2142 |
|
Proper sequence to configure FastEthernet0 from user EXEC mode |
Step 1: Enable Step 2: configure terminal Step 3: interface fastethernet0 |
|
What are two features that are associated with single-mode fiber-optic cable (Choose Two)
A) a single strand of glass fiber B) Carried higher bandwidth that multimode fiber C) cost is less that multimore fiber D) operated over less distance that multimore fiber |
1) a single strand of glass fiber
2) Carries higher bandwidth that multimode fiber |
|
Which three pieces of information about a device can be seen from the show version command? (Chose three) A) CPU load B) Device model C) Installed DRAM D) Installed flash E) Locally configured IP addresses |
1) Device model
2) Installed DRAM
3) Installed flash |
|
From a Windows command prompt, which command displays the local IP address of a computer |
ipconfig |
|
Which command initiates the copy of an IOS image to a Cisco device? |
copy tftp flash |
|
The pins and RJ-45 are numbered from 1 through 8. With the material points of the plug facing toward you, pin 1 in the leftmost pin. Which two sets are looped on an RJ-45 T1 loopback plug? |
Pins 1 and 4
Pins 2 and 5 |
|
Which layer of the IOS model defines how data is formatted for transmission and how access to the physical media is controlled? |
Data link |
|
Which two of the following statements are true? (Choose two)
A) OEM products that are built for Cisco never get a Cisco logo applied B) The Cisco logo, old or new can be found on the front bezel of all Cisco rack-mountable or desktop products. C) Serial number are attached by label on all Cisco field-replaceable parts D) At the network module level, the model number is the same as the part number |
1) The Cisco logo, old or new can be found on the front bezel of all Cisco rack-mountable or desktop products.
2) At the network module level, the model number is the same as the part number |
|
When using a modem to provide out-of-band access to a Cisco router, which cable type is used to connect the wall jack to the modem? |
RJ-11 to RJ-11 |
|
Which command initiates copying the save configuration of a Cisco device to a TFTP server? |
copy startup-config tftp |
|
Which port displays the bootup process on a Cisco device? |
Console |
|
Which two of the following are component of WAN connection? (Choose two)
A) Router B) Switch C) CSU/DSU D) Hub E) Bridge |
1) Router
2) CSU/DSU |
|
Which interface card is an encryption module? NME-VMSS-16 NME-CUSP-5222 AIM-VPN/SSL-3 M-1A-OC3-POM |
AIM-VPN/SSL-3 |
|
Which address facilitates the routing of packets over an IP network? |
network |
|
Which type of memory stores the decompressed form of the Cisco IOS software and the running configuration? |
DRAM |
|
Which of the following best describes how to assign a static IP address to the Ethernet port on a computer? |
From Network connections, double-click Local Area Connection, Click Protocol (TCP/IP), Click properties, click the use the Following Address button, and the configure the IP information |
|
Which two pairs of LAN Ethernet devices use an RJ-4 Straight-through cable? (Chose two)
|
1) Switch to router
2) Switch to server |
|
Which two comands display the saved configuration file? (Choose two) |
show configuration
show startup-config |
|
What is the default operating mode you are initially logging into a router? |
user EXEC |
|
Which two modules can be plugged into internal advanced integration module (AIM) slots on a Cisco router? (Chose two) |
Virtual private network module
Intrusion detection system module |
|
TFTP is a simple protocol files, such as a Cisco IOS or configuration file, from one device to another. Wich device cannot be configured to be used as a TFTP server? |
Modem |
|
Which three of the following statements are true about a smart jack? (Chose three) |
1) it provides signal conversion
2) it regenerates the signal to compensate for signal degradation from line transmission
3) it proves loopback testing |
|
Which command indicates the amount of memory (NVRAM,RAM, and flash) in as Cisco device? |
show version |
|
ESD is the sudden and momentary electric current that flows between two different object at difference eletrical potentials caused by direct contact or induced by an electrostatic field. Which three of the following tools should be used to avoid ESD? (Choose two) |
ESD wrist strap
Antistatic bag
Antistatic mat |
|
Which three of the following statements are true? (Choose three) |
Each IP address has two parts: a network ID and a host ID
An IP subnet equals a broadcast domain
A subnet address is created by borrowing bits from the original host ID |
|
The colored wires at one end of the cable in the reverse sequence of the colored wires at the other end of the cable. Which cable does this describe. |
Rolled |
|
Into which port do you insert the card? |
Gigabit Ethernet |
|
Which two of the following are installed fiber-optic connections? (Choose two) |
subscriber
Lucent |
|
Which command initiates the transfer of a Cisco IOS image over IP from ROMMON |
tftpdnld |
|
Which of the following best describes the cable that is used to connect a laptop to an Ethernet port on a Cisco router? |
Crossover |
|
Which three of the following describe Fast Ethernet? (Choose three) |
100BASE-T
100-Mb's speed
requires Category 5 or higher UTP cabling |
|
When using a modem to provide out-of-band access to a Cisco router, which cable is used to connect the modem to the router? |
DB-25 to RJ-45 |
|
Which bits represent the boot field in the configuration register value A) A highest two bits B) highest four bits C) lowest two bits D) lowest four bits |
lowest four bits |