Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
31 Cards in this Set
- Front
- Back
0x2142
|
boots normal but ignores startup config.
|
|
0x2101
|
bootstrap
|
|
0x2102
|
default or normal.
loads ios from flash then startup from NVRAM |
|
0x2120
|
Rom Monitor mode
|
|
what are the 3 commands to permit only 1 host to access telnet. using standard ACLs
|
#access-list 1 permit 192.168.1.2
#line vty 0 4 #access-class 1 in |
|
what are the multicast addresses of.
OSPF-hello packets OSPF-flooding packets RIP2- EIGRP- |
OSPF-hellos 224.0.0.5
OSPF-flooding 224.0.0.6 RIP-224.0.0.9 EIGRP-224.0.0.10 |
|
what is the problem when #show ip eigrp topology. Consistantly returns the same routes but u cannot connect to the route and it is active.
|
EIGRP is said to be (SIA) stuck in active. issue the command #timers active-time. and increase the amount of time the router queries.
|
|
Routes that orginates in.
1. another OSPF area? 2. same OSPF area Are called? And how r they identified the the routing table? |
1. inter-area routes. "0 IA"
2. intra-area route. "0" |
|
Use ISL or 802.1q for trunking protocol between switch & router?
|
802.1q.
ISL is not a trunking protocol, it simply identifies with vlan a frame goes to. |
|
Boot field in Configuration Register is set to.
0 (0x0) 1 (0x1) |
0 (0x0) - ROM monitor mode
1 (0x1) - System loads from ROM 2 - f (0x2 - 0xF) - creates a default boot filename for booting from a network server. Two is the default. |
|
Command to config a ip addy to a hostname on a router?
|
#ip host [hostname] [ip_address]
|
|
command to set password for priviledge exec level 12?
|
#enable password level 12 applesauce
|
|
packets transfer from one lan to another what addresses changes?
|
source mac
destination mac |
|
which layers of the OSI model does TCP/IP stack correspond?
|
layer 3-7
|
|
command to see ip address of connected CPD devices.
|
#show cdp neighbor detail
|
|
2 commands to configure a switch/bridge to be the Root on VLAN 10?
|
#spanning-tree vlan 10 root priority
#spanning-tree vlan priority 8192 |
|
whats default priority # for STP?
What priority # does the following command enable. #spanning-tree vlan 10 root primary. |
-default priority # is 32768.
-#spanning-tree vlan 10 root primary---># is 24576 |
|
command used to setup password authentication on ospf?
|
#IP OSPF authentication-key
|
|
command used to view which processes are running and how much cpu is being used?
|
#show processes cpu
|
|
command to config turbo acl.
|
#access-list compiled
|
|
DUAL-3-SIA indicates what?
|
eigrp is SIA.
|
|
what is a MDF?
|
Main Distribution Frame, usually at the CO or central point.
|
|
what is a IDF?
|
Intermediate Distribution Frame.
Connects the users to the MDF. Secondary communications room. |
|
what is VCC?
|
vertical cross-connect.
|
|
what is HCC?
|
horizontal cross-connect.
wiring closet where horizontal cabling connects to a patch panel which is connected by backbone cabling to the MDF. |
|
whats does [ ] specify?
|
the default value.
|
|
what does #show history do?
|
shows the last 10 commands entered in system.
|
|
suspend telnet?
|
Cntr - Sht - 6 then x
|
|
#show spanning-tree
can be verified on VLAN by looking at? |
VLAN is in spanning-tree procotol.
|
|
command to display all ip routing procotl>
|
show ip protcol
|
|
command ot display sap table.
|
#show ipx server
service access pont. |