Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
32 Cards in this Set
- Front
- Back
The allowance for boats for shore stations is
established by what authority? 1. Naval district commander 2. Chief of Naval Operations 3. Commander, Naval Sea Systems Command 4 . Fleet commanders |
3. Commander, Naval Sea Systems
Command |
|
Where can you find a list of all the items in a
boat’s outfit? 1. Naval Ships’ Technical Manual 2. Coordinated Shipboard Allowance List 3. Afloat Shopping Guide 4. Federal Stock Catalog |
2. Coordinated Shipboard Allowance List
|
|
Under what condition is a boat outfit retained
on board when the boat is turned in for disposal? 1. When the boat is to be replaced by one of a different type 2. When the ship has other boats that may use the equipment 3. When the boat is to be replaced by another of the same type 4. When the boat is to be scrapped |
3. When the boat is to be replaced by
another of the same type |
|
Which of the following lines is required for
use as a swimmer’s/survivor’s tending line? 1. 200 yards of orange dacron line 2. 275 yards of three-strand nylon 3. 300 yards of yellow polypropylene 4. 325 yards of plaited nylon |
3. 300 yards of yellow polypropylene
|
|
Regulations and guidelines for a ship’s boat
bill are set forth in which of the following manuals? 1. OPNAVINST 3 120.32 2. NSTM, Chap 583 3. OPNAVINST 5100.19 4. NAVSHlPS 250-452 |
1. OPNAVINST 3 120.32
|
|
Which of the following is a safety precaution
you should observe while servicing a power boat? 1. Keep all oily cleaning rags in an open container 2. Keep the hinged covers on the engine hood closed during refueling 3. Charge the batteries in an open space only 4. Open the fuel tank cutoff valves before refueling |
3. Charge the batteries in an open space
only |
|
When and where should the fueling of
powerboats be accomplished? 1. During daylight in the skids 2. At night swung over the side 3. During daylight hours in the water 4. At first light in the skids |
3. During daylight hours in the water
|
|
When fueling a 26-foot MWB, where is the
grounding wire attached? 1. The engine hood 2. A bilge strake 3. On the deck plate 4. The copper, gooseneck vent pipe |
4. The copper, gooseneck vent pipe
|
|
What sequence of the events should you
follow when you have completed fueling a boat: (a) remove the nozzle, (b) detach the grounding wire, (c) close the flap, (d) screw on the cap? 1. A, c, d, b 2. B, a, c, d 3. C, a, b, d 4. D, b, c, a |
1. A, c, d, b
|
|
The hoisting sling manufactured for a MWB
weighing 6,500 pounds must pass a load test for how many pounds? 1. 6,500 2. 9,750 3. 13,000 4. 16,500 |
3. 13,000
|
|
As a general rule, ship’s personnel make a
thorough inspection of boat slings for possible deterioration or rusting whenever they notice which of the following conditions? 1. Wearing of the serving 2. Stretching of the slings 3. Stretching of the side guys 4. Wearing of the side guys |
1. Wearing of the serving
|
|
Who is responsible for making a boat ready for hoisting out?
1. Hatch captain 2. Engineer 3. Division LPO 4. Coxswain |
4. Coxswain
|
|
If the sea is rough when you are preparing to
launch a boat by crane, what steadying-lines arrangement should you provide? 1. Two inboard, one astern, and one forward 2. One inboard, two outboard, and one astern 3. One inboard and two outboard 4. Two inboard, two outboard, and one forward |
1. Two inboard, one astern, and one
forward |
|
When you are launching a boat from the side
of the ship, what should be done as soon as the boat is waterborne? 1. Start the engine of the boat 2. Trip the slings 3. Cast off the sea painter 4. Steer the boat from the ship’s side |
2. Trip the slings
|
|
While hoisting a boat aboard by crane, when
are the steadying lines passed to the boatcrew? 1. After the sea painter is secured to the boat 2. After the slings are secured to the boat 3. As soon as the boat comes alongside 4. As soon as the slings are connected to the tripping line |
1. After the sea painter is secured to the
boat |
|
While hoisting a boat, when should passengers
and crew disembark? 1. Before the boat is hoisted from the water 2. As soon as the boat is clear of the water 3. When the boat is at the lowest weather deck 4. After the boat is in the skids |
3. When the boat is at the lowest weather
deck |
|
What type of boat is used on a SLAD davit?
1. Motorwhale 2. LCPL 3. RIB 4. LCM 8 |
3. RIB
|
|
The modified gravity davits differ from the
unmodified davits in that the modified davits lack which of the following devices? 1. Keeper bars 2. Strongback pins 3. Moveable blocks 4. Limit switches |
3. Moveable blocks
|
|
Which of the following types of davits may
be rigged for stowing and handling up to four boats? 1. Radial or round bar 2. Quadrantal 3. Gravity 4. Crescent |
3. Gravity
|
|
The double-link pivoted gravity davit will
hoist a fully loaded boat how many feet per minute? 1. 20 2. 25 3. 30 4. 40 |
4. 40
|
|
What procedure is eliminated by using the
single-arm davit? 1. The process of threading two hooks through bow and stern hoisting rings 2. The use of a sea painter 3. The use of frapping lines 4. The use of steadying lines |
1. The process of threading two hooks through bow and stern hoisting rings
|
|
The purpose of the falls tensioning device is
to 1. prevent the falls from twisting 2. keep the slack out of the falls while hooking on and unhooking 3. prevent the falls from two-blocking 4. prevent the falls from toppling |
2. keep the slack out of the falls while
hooking on and unhooking |
|
On the Raymond release hook, why is the
outer end of the tripper weighted? 1. So that when the boat is in the water, the hook will remain engaged until the ring is lifted out 2. When the boat is in the water the load is removed by the tripper 3. To provide a harder striking surface for the ring 4. To keep the falls from flopping around with the rise and fall of the wate |
1. So that when the boat is in the water, the
hook will remain engaged until the ring is lifted out |
|
Where should the monkey lines tend while
lowering a boat to prevent them from fouling on an object or structure in the boat? 1. Over and inboard, between the ship and the boat 2. Inside the boat, coiled on deck 3. Over the outboard side of the boat, away from the ship 4. Hand tended from the deck of the ship to the inside of the boat |
1. Over and inboard, between the ship and
the boat |
|
Once waterborne, what is the sequence of
events that you should use in casting off a boat(a) Cast off forward (b) Cast off aft (c) Cast off the sea painter (d) Cast off the steadying lines? 1. A, c, d, b 2. B, a, c, d 3. B, a, d, c 4. D, b, c, a |
3. B, a, d, c
|
|
When a boat is to be hoisted in by davits,
what is the first line a boatcrew secures? 1. Frapping line 2. Monkey line 3. Steadying line 4. Sea painter |
4. Sea painter
|
|
The standard shipboard allowance of inflatable
lifeboats is a quantity that will provide for what percentage of a ship’s crew? 1. 85% 2. 100% 3. 110% 4. 125% |
2. 100%
|
|
The primary difference between the Mk 5
Mod 2 and the Mk 6 inflatable lifeboat is that the 1. Mk 5 Mod 2 is in a ridged container 2. Mk 6 is in a ridged container 3. Mk 5 Mod 2 holds more people 4. Mk 6 holds more people |
4. Mk 6 holds more people
|
|
At what depth is the automatic launching
feature on inflatable lifeboats designed to activate? 1. 30 to 60 ft 2. 20 to 50 ft 3. 10 to 40 ft 4. 5 to 15 ft |
3. 10 to 40 ft
|
|
What degree of lip is designed on the standard
Navy lifeboat stowage cradle to prevent the encapsuled lifeboat from falling out? 1. 10° 2. 15° 3. 20° 4. 25° |
2. 15°
|
|
What is the size of nylon cord that is attached
to the shackle of the hydrostatic release and passed through the thimble of the wire rope harness? 1. 1/4 in. 2. 1/2 in. 3. 3/4 in. 4. 5/8 in. |
1. 1/4 in.
|
|
After installation of the hydrostatic release
device, in which direction must the actuating mechanism face? 1. Inboard for access and to prevent accidental release 2. Inboard for protection against the weather 3. Outboard to prevent accidental release 4. Outboard and painted to highlight its location |
3. Outboard to prevent accidental release
|