Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
30 Cards in this Set
- Front
- Back
Which SSL 4000 G+ mode is pictured above? (Mix Mode Diagram) |
Mix Mode |
|
The Input and Output buttons in Monitor Input section override the Ready Group and Ready Tape Buttons. True or False. |
True |
|
When working in Mix mode on the console, it is possible use the small fader as an extra aux send by: |
Choosing an input/output selection, assigning a bus outputted patching that bus output to an effects input. |
|
On the SSL in the Mix status, the small fader will receive input signal at which Patch point? |
Tape Monitor Inputs |
|
Which is the preferred tracking status on the SSL: |
Recording and VCA’s to monitor (Fader Reverse) |
|
In Mix status to configure the small fader to receive a post VCA signal which button must be selected in the Monitor input section? |
Output Only |
|
Which insert point on the patchbay should be used when inserting an outboard compressor across the mix so that the compression will follow the output of the master fader? |
Post VCA Insert LF and RF |
|
Why do most engineers who work on the SSL G+ prefer to use channels as returns for effects rather than the stereo echo returns? |
All of these choices |
|
If a group of channels is being bussed to group 12, then routed to Pro-Tools channel 8, which channels Group Trim will attenuate the level of the track in Pro-Tools if the level is too hot? |
Channel 12 Group Trim |
|
How many rows are there in the patchbay for the Multitrack returns (Pro-Tools outputs)? |
2 |
|
The Channel Out button in the dynamics section routes the signal: |
Post EQ then to Dynamics |
|
Which SSL 4000 G+ mode is pictured above? (Record & VCA Mode Diagram) |
Record & VCA to Monitor (fader reverse) mode |
|
The Ready Tape button in the Monitor Input section of each channel derives its signal from: |
The Multitrack Return |
|
“I” on the thumbwheel setting stands for ___, which means that the faders set to this are not affected by the master VCA trim. |
Independent |
|
Why does an SSL G+ channel compressor not have a make-up or gain parameter? |
Because the channel compressors feature auto-gain compensation |
|
The “Subgroup” button at the input section of the channel path on module 20 takes its feed from? |
Group 20 |
|
The Default solo on the SSL is? |
Solo in Place (destructive) |
|
The ’Split’ button for the filters on the SSL puts the filters: |
directly after the input of the channel path. |
|
Which button on the SSL module switches the ‘mic/line’ Input to the channel path per module against the master status? |
Flip |
|
What button in the Center Section allows you to see the input level post Mic or Line pre on the channel’s VU meter? |
Channel into Meters |
|
What button allows you to send the Mix bus output directly to the cues (Headphones)? |
Quad to Cues |
|
What is the normal SMPTE patch so the SSL computer can read SMPTE from the analog multitrack? |
Multitrack Return 24 to ‘Read’ patch point |
|
Which SSL 4000 G+ mode is picture above? (Record Mode Diagram) |
Record Mode |
|
The first 8 outputs of Pro Tools are normally to what modules? |
25-32 |
|
If working in Mix mode on the SSL 4000 G+ console, what happens to the channels signal at the large fader when the Float button is pressed? |
The signal is routed to the routing matrix and disconnected from the Quad Bus |
|
With both the Insert button and Pre button selected on a channel, the insert point will be located where in signal flow? |
Pre EQ and Pre Fader |
|
When working in Mix mode on the SSL console at S.A.E., it is possible to return effects to: |
All of these choices |
|
When setting up a separate headphone mix from the SSL channel using the stereo cue send, how would you hear the cue mix in the control room to set up a good blend for the musicians? |
External to Monitors button and select Cue Stereo |
|
The SSL G+ console can only be used in-line, it cannot be used in a split bus fashion. True or False |
False |
|
The thumbwheel settings on each channel of the console are used for: |
VCA Subgrouping |