Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
29 Cards in this Set
- Front
- Back
10.01
Which of the following protocols support VLSM, summarization, and discontiguous networking? (Choose three.) A. RIPv1 B. IGRP C. EIGRP D. OSPF E. BGP F. RIPv2 |
Which of the following protocols support VLSM, summarization, and discontiguous networking? (Choose three.) A. RIPv1 B. IGRP C. EIGRP D. OSPF E. BGP F. RIPv2 |
|
10.02 Which of the following are considered distance-vector routing protocols? (Choose two.) A. OSPF B. RIP C. RIPv2 D. IS-IS |
Which of the following are considered distance-vector routing protocols? (Choose two.) A. OSPF B. RIP C. RIPv2 D. IS-IS |
|
10.03 Which of the following are considered link-state routing protocols? (Choose two.) A. OSPF B. RIP C. RIPv2 D. IS-IS |
Which of the following are considered link-state routing protocols? (Choose two.) A. OSPF B. RIP C. RIPv2 D. IS-IS |
|
10.04 Which of the following is considered a hybrid routing protocol? A. OSPF B. BGP C. RIPv2 D. IS-IS E. EIGRP |
Which of the following is considered a hybrid routing protocol? A. OSPF B. BGP C. RIPv2 D. IS-IS E. EIGRP |
|
10.05 Why would you want to use a dynamic routing protocol instead of using static routes? A. Less overhead on the router B. Dynamic routing is more secure C. Dynamic routing scales to larger networks D. The network runs faster |
Why would you want to use a dynamic routing protocol instead of using static routes? A. Less overhead on the router B. Dynamic routing is more secure C. Dynamic routing scales to larger networks D. The network runs faster (FYI -- Networks may actually run slower using dynamic routing since the processor devotes some processor time and interface bandwidth to converge routing tables.) |
|
10.06 Which of the following is a vendor-specific routing protocol? A. IGRP B. OSPF C. RIPv1 D. EIGRP E. IS-IS F. None of the above |
Which of the following is a vendor-specific routing protocol? A. IGRP B. OSPF C. RIPv1 D. EIGRP E. IS-IS F. None of the above (Cisco made EIGRP available in early 2013.) |
|
10.07 RIP has a long convergence time and users have been complaining of response time when a router goes down and RIP has to reconverge. Which can you implement to improve convergence time on the network? A. Replace RIP with static routes B. Update RIP to RIPv2 C. Update RIP to OSPF using Link State D. Replace RIP with BGP as an exterior gateway protocol |
RIP has a long convergence time and users have been complaining of response time when a router goes down and RIP has to reconverge. Which can you implement to improve convergence time on the network? A. Replace RIP with static routes B. Update RIP to RIPv2 C. Update RIP to OSPF using Link State D. Replace RIP with BGP as an exterior gateway protocol |
|
10.08 What is the administrative distance of OSPF? A. 90 B. 100 C. 110 D. 120 |
What is the administrative distance of OSPF? A. 90 B. 100 C. 110 D. 120 |
|
10.09 Which of the following protocols will advertise routed IPv6 networks? A. RIP B. RIPng C. OSPFv2 D. EIGRPv3 |
Which of the following protocols will advertise routed IPv6 networks? A. RIP B. RIPng C. OSPFv2 D. EIGRPv3 |
|
10.10 What is the difference between static and dynamic routing? A. You use static routing in large, scalable networks B. Dynamic routing is used by a DNS server C. Dynamic routes are added automatically D. Static routes are added automatically |
What is the difference between static and dynamic routing? A. You use static routing in large, scalable networks B. Dynamic routing is used by a DNS server C. Dynamic routes are added automatically D. Static routes are added automatically |
|
10.11 Which routing protocol has a maximum hop count of 15? A. RIPv1 B. IGRP C. EIGRP D. OSPF |
Which routing protocol has a maximum hop count of 15? A. RIPv1 B. IGRP C. EIGRP D. OSPF |
|
10.12 Which of the following describes routing convergence? A. The time it takes for your VPN to connect B. The time required by protocols to update their forwarding tables after changes have occurred C. The time required for IDS to detect an attack D. The time required by switches to update their link status and go into forwarding state |
Which of the following describes routing convergence? A. The time it takes for your VPN to connect B. The time required by protocols to update their forwarding tables after changes have occurred C. The time required for IDS to detect an attack D. The time required by switches to update their link status and go into forwarding state |
|
10.13 What routing protocol is typically used to connect AS’s on the Internet? A. IGRP B. RIPv2 C. BGP D. OSPF |
What routing protocol is typically used to connect AS’s on the Internet? A. IGRP B. RIPv2 C. BGP D. OSPF |
|
10.14 RIPv2 sends out its routing table every 30 seconds just like RIPv1, but it does so more efficiently. What type of transmission does RIPv2 use to accomplish this task? A. Broadcasts B. Multicasts C. Telecast D. None of the above |
RIPv2 sends out its routing table every 30 seconds just like RIPv1, but it does so more efficiently. What type of transmission does RIPv2 use to accomplish this task? A. Broadcasts B. Multicasts C. Telecast D. None of the above |
|
10.15 Which routing protocols have an administrative distance of 120? (Choose two.) A. RIPv1 B. RIPv2 C. EIGRP D. OSPF |
Which routing protocols have an administrative distance of 120? (Choose two.) A. RIPv1 B. RIPv2 C. EIGRP (AD of 90) D. OSPF (AD of 110) |
|
10.16 Which of the following routing protocols uses AS-Path as one of the methods to build the routing tables? A. OSPF B. IS-IS C. BGP D. RIP E. EIGRP |
Which of the following routing protocols uses AS-Path as one of the methods to build the routing tables? A. OSPF B. IS-IS C. BGP D. RIP E. EIGRP |
|
10.17 Which IPv6 routing protocol uses UDP port 521? A. RIPng B. EIGRPv6 C. OSPFv3 D. IS-IS |
Which IPv6 routing protocol uses UDP port 521? A. RIPng B. EIGRPv6 C. OSPFv3 D. IS-IS |
|
10.18 What EIGRP information is held in RAM and maintained through the usage of hello and update packets? (Select all that apply.) A. DUAL table B. Neighbor table C. Topology table D. Successor route |
What EIGRP information is held in RAM and maintained through the usage of hello and update packets? (Select all that apply.) A. DUAL table B. Neighbor table C. Topology table (EIGRP holds 3 tables in memory: Routing, Topology and Neighbor. Routing is share, but each router builds their Neighbor and Topology tables using hello packets.) D. Successor route |
|
10.19 Which is true regarding EIGRP successor routes? A. Successor routes are saved in the neighbor table. B. Successor routes are stored in the DUAL table. C. Successor routes are used only if the primary route fails. D. A successor route is used by EIGRP to forward traffic to a destination. |
Which is true regarding EIGRP successor routes? A. Successor routes are saved in the neighbor table. B. Successor routes are stored in the DUAL table. C. Successor routes are used only if the primary route fails. D. A successor route is used by EIGRP to forward traffic to a destination. (Successor routes are preferred routes in EIGRP. Think "successful." They are stored in the routing table.) |
|
10.20 Which of the following uses only hop count as a metric to find the best path to a remote network? A. RIP B. EIGRP C. OSPF D. BGP |
Which of the following uses only hop count as a metric to find the best path to a remote network? A. RIP B. EIGRP C. OSPF D. BGP |
|
10.21 The default administrative distance of RIP is___________________? |
120 |
|
10.22 The default administrative distance of EIGRP is___________________? |
90 |
|
10.23 The default administrative distance of RIPv2 is___________________? |
120 |
|
10.24 The default administrative distance of a static route is___________________? |
1 |
|
10.25 What is the version or name of RIP that is used with IPv6? |
RIPng (Next Generation). |
|
10.26 What is the version or name of OSPF that is used with IPv6? |
OSPFv3 |
|
10.27 What is the version or name of EIGRP that is used with IPv6? |
EIGRPv6 |
|
10.28 When would you use BGP? |
To connect two autonomous systems (ASs) together |
|
10.30 Is BGP considered link state or distance vector? |
Neither. BGP is a path vector protocol. |