Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
48 Cards in this Set
- Front
- Back
What type of code is AK7
|
supply project code
|
|
Your squadron is categorized as a FAD II activity and you require a mission essential part. What is the highest priority that can be assigned to your request?
|
2
|
|
When a FAD III is assigned to your activity, what is the highest priority you should use to order routine replenishment stock?
|
13
|
|
Information from what source is used by supply department personnel as justification for stocking material?
|
usage statistics
|
|
What type of code identifies the agent or agency that has design control over an item?
|
CAGE
|
|
What is the purpose of an illustrated parts breakdown?
|
To allow supply and maintenance personnel to identify and order replacement parts for aircraft or equipment
|
|
What section in an IPB contains general information and instructions for using the publication?
|
Introduction
|
|
Besides the introduction, each IPB includes what information?
|
Table of contents or alphabetic index, group assembly parts list, and numerical index
|
|
What section of the IPB contains an explanation of the source or SM&R codes used in the IPB
|
Introduction
|
|
What listing in the IPB lists aircraft assemblies and identifies the pages or figure numbers where the assemblies are shown in the IPB?
|
Alphabetical index
|
|
What section of the IPB contains a description of a component listed in the IPB
|
Group assembly parts list
|
|
What section of the IPB lists supplementary handbooks to which you may refer?
|
Introduction
|
|
What is the purpose of an index number in an IPB
|
to establish the relationship between parts in the illustration and the corresponding parts list
|
|
T/F An SM&R code is a five or six position alphanumeric code.
|
True
|
|
What part of a part's SM&R code indicates how the part is to be acquired?
|
Source code only
|
|
What position of the SM&R code identifies the maintenance level assigned to completely repair an item?
|
Fourth
|
|
What information does the third position of an SM&R code provide?
|
The lowest maintenance level authorized to remove, replace, and use item
|
|
When removal of a component from an aircraft is not feasible or advisable until a replacement is on hand, supply personnel can exempt the turn-in of the component (retrograde) if its part number is listed in what document?
|
CRIPL
|
|
What ASO publication contains a complete list of Navy-managed material that is classified as MTR?
|
MRIL
|
|
What type of material is listed in the CRIPL?
|
material exempt from the one-for-one turn-in rule
|
|
The reference number on a master cross-reference list refers to what number or numbers?
|
Either a manufacture's part number, a drawing number, or a design control number.
|
|
The MCRL is used to provide a cross-reference between what items of information?
|
Reference number and NSN
|
|
What is the purpose of the ICRL-A?
|
To provide a list of repairables and the local IMA's capability to repair them.
|
|
An ICRL-A is revised at what specified interval?
|
Quarterly
|
|
What ICRL Capability code is used for check and test only?
|
A1
|
|
Within the iCRL listing, what code is equivalent to Beyond Capability of Maintenance (BCM)-3
|
X3
|
|
To what reference should you refer to obtain an NSN or reference number for an item when you only know the description?
|
ASG
|
|
What is the 13-digit number called that identifies an item of material in the supply system?
|
NSN
|
|
What is the title of the overall program that provides the data required for effective management of support equipment at all levels of maintenance?
|
AMMRL
|
|
What command exercises overall program management for the AMMRL program?
|
NAVAIRSYSCOM
|
|
What information is provided by the first two digits in the FSC code number
|
The major or broad category of the stock
|
|
The NSN is comprised of what total number of digits?
|
13
|
|
What acronym identifies equipment that is required on the ground to make a system, subsystem, or end item of equipment operational?
|
SE
|
|
Within an activity, personnel in what rating normally maintain the IMRL?
|
AK
|
|
The IMRL contains how many major section?
|
5
|
|
At the organizational maintenance level, the point of contact for all material requirements generated y a squadron is located in what organization?
|
Material control center
|
|
What Material Condition Code tells you that an iem of supply is fast moving and in high demand?
|
F
|
|
To determine whether an intermediate maintenance activity has capability to test/check or repair an item, what I-level supply area screens all components turned into ASD/SSC?
|
AMSU
|
|
The ASD/SSC is composed of what section or sections?
|
SRS and CCS
|
|
The SRS limits the quantity of any item in the pre-expended bin to a 30 day supply.
|
True
|
|
Within an activity, what officer must approve the item of PEB stockage when it costs more then $150?
|
The commanding officer
|
|
Supply will remove an item from the PEB if there has been no demand for the item within what total period of time?
|
1 year
|
|
What is the purpose of the component control section within the supply department?
|
To manage the LRCA at the ASD/SSC
|
|
A LRCA is assigned a workload priority. The priority assigned is one of what total number of priorities that can be assigned to the LRCA
|
4
|
|
An aircraft is NMCS/PCS status. What priority is assigned to LRCA in support of this aircraft?
|
Priority 1
|
|
AK0
|
Assigned only when requisitioning material to restore an aircraft to mission capable status.
|
|
AK7
|
Assigned when requisitioning material to return mission essential subsystems to an operational condition when an aircraft is in a partial mission capable status.
|
|
ZA9
|
forced high-time removal items required for immediate end use on primary mission weapons systems.
|