Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
200 Cards in this Set
- Front
- Back
- 3rd side (hint)
What is the maximum towing speed for Aircraft
|
5 MPH or as fast as the slowest Wing Walker
|
|
|
What is the required tail wheel pressure range for the MH-60R
|
105 PSI +/- 5 PSI
|
|
|
As a PC you are preparing to launch an aircraft when you notice an unsecured doghouse on the Flight line, What should you do? |
Hold launching A/C until Doghouse is secured
|
|
|
What body part is pointed to in order to indicate an Internal / External Fire |
Internal: Mouth
External: Ear |
|
|
What is the fire extinguishing agent aboard the aircraft fire bottles? |
Halon |
|
|
Is there such a thing as a "combat Daily Inspection"? |
Absolutely not
|
|
|
What is the hangar bay fire extinguishing agent? |
AFFF
|
|
|
What are the five steps of ORM? |
1. Identify Hazards 2. Assess Hazards 3. Make Risk Decisions 4. Implement Controls 5. Supervise |
|
|
Where is the SDS located? Safety Data Sheet |
In the Hangar near Tool Room
|
|
|
|
Call the AO's |
|
|
How many people are needed to move an aircraft? |
7 (for Hangar), 6 (w/ brakes), 7 (w/o brakes(Two chock walkers, no B/R))
|
|
|
|
2 Wing walkers 1 Brake rider 1 PC 1 Tow tractor driver 1 Safety observer. |
|
|
What must you do prior to moving an Aircraft? |
Pre–Op the S.E. and Preform a Move Brief in Maintenance Control. |
|
|
|
5 (3 pole, 1 stab, 1 strut) |
|
|
What is the Max wind speed that you can fold or spread the blades |
45 knots FROM ANY DIRECTION!!! |
|
|
What are the differences between Hydraulic Pumps? |
Pumps 1 & 2 are driven by the Accesory MODs Pump 3 (The B/U) has it's own electric motor Pump 4 (Utility) is driven by the MGB |
|
|
How Long after a move should wait you check fuel samples? |
2 hours
|
4790.2(series) Chapter 10 |
|
What does MIM stand for? |
Maintenance Instruction Manual |
|
|
What does NALCOMIS stand for? |
Naval
Aviation Logistics COmmand Management Information System |
|
|
What is the MIL Spec for Engine/ APU oil/ |
MIL–PRF–23699
|
|
|
What is the MIL SPEC for transmission oil? |
DOD–PRF–85734
|
|
|
What is the restricted fuel for this aircraft and why? |
JP–4, Because of it's Low Flash Point
|
|
|
Starboard to Port? |
Forward, Aft, Lateral
|
|
|
Port to Starboard? |
Yaw, Roll, Pitch, and Collective
|
|
|
Can you check the oil of the IGB with the tail folded? |
No, tail folds at a slant
|
|
|
What are Electromechanical Trim Servos and where are they located? |
Yaw and Collective, located in the far front of the Hydrualics Bay
|
|
|
|
Within the bullseye or between the two lines. |
|
|
What is the pressure range for the rotor brake? |
450–690 PSI
|
|
|
What are the two types of trim servos/ |
Hydromechanical and Electromechanical
|
|
|
|
2 PSI |
|
|
What do the high speed shafts do? |
Take power from the engines to spins the Input Modules
|
|
|
What is the maximum (unsafe) fuel capacity without the AUX tank? |
600 Gallons |
|
|
What is the NATO Code JP-5? |
F-44
|
|
|
What is the NATO Code JP-8? |
F-34
|
|
|
What is the NATO Code JP-4? |
F-40
|
|
|
How much does a single gallon of JP-5 weigh? |
6.8 pounds |
|
|
What is the maximum pressure for de-fueling inside the fuel cell? |
–3 PSI
|
|
|
|
CO2 |
|
|
What is the tire pressure range for the main landing gear |
100 psi +/- 5 PSI
|
|
|
What does SDS stand for? |
Safety Data Sheets
|
Think HAZMAT |
|
What flight control surfaces have Hydro-Mechanical trim servos?
|
Roll and Pitch |
|
|
How long after shut down can you check the APU oil level? |
1 hour
|
|
|
How long after shut down must you wait to be able to check engine oil level? |
20 minutes
|
|
|
What drives the Accessory Modules?
|
The Input Modules |
|
|
What is the Ground Safety Manual? |
NAVAIR 00–80T–96
|
|
|
What is the wind restrictions when folding the Tail Pylon? |
45 knots FROM ANY DIRECTION!!!!
|
|
|
The MRC-100 is used for what? |
A Turnaround Inspection
|
|
|
In what publication can you find A/C movement procedures? |
GAI–010 or 17–1–537 |
|
|
How many people are required to spread the tail pylon? |
5 Total: 3 on the fold pole, 1 on the hand hold of the stabailator, and one on the 7/8" Speed Wrench and Pylon Strut |
|
|
How many people (minimum) are required to move an Aircraft? |
6 people:
1 PC, 2 Wing walkers, 1 Safety Observer, 1 Tow Tractor Driver, 1 Brake Rider |
|
|
What is PRIST and what is the restriction? |
It is an Anti-Icing agent that is premixed with fuel; PRIST in an aerosol can is NOT authorized |
|
|
Who can Suspend/Revoke your PC qualification? |
CO, though the MO can recommend
|
|
|
What does the "Coffee Can" service? |
Pump 1, Pump 2, Back up, Utility Pump, Rotor Brake
|
|
|
What is the First WARNING when connecting external power? |
Ensure area around the STAB is clear of personnel |
|
|
How long after shutdown can you check MGB Oil?
|
Hot side: 1/2 hour – 2 hours,
Cold side: over 2 hours |
|
|
What is the Precaution when opening the Nose Door?
|
Watch out for dripping water in avionics
|
|
|
What does RAST stand for
|
Recovery
Assist Securing Traverse |
|
|
At what wind condition does not allow for stab or blade fold? |
45 knots
|
|
|
How long is a daily good for? |
72 hours unless there is major maintenance or flight
|
|
|
How many CADs are on the Aircraft (w/out armament) Total & Locations? |
7 Total: 2 x each fire bottles, 1 RAST Probe, 1 Rescue Hoist, 1 ALFS or Cargo Hook |
|
|
What are the 5 parts of a Blade |
Tip Cap, Trim Tab, Center line, Spar, Root |
|
|
Which inspection do you check for servicing?
|
Turnaround Inspection
|
|
|
How long is a turnaround good for? |
24 hours unless major maintenance or flight
|
|
|
What is the MIL Specification A/C wash soap? |
MIL-PRF-85570 Type II
|
|
|
When towing the A/C when do you unlock the Tail Wheel? |
Only after attaching the tow bar
|
|
|
What does a "C" annotate in a daily deck? |
Corrosion prone area |
|
|
In what publication is the Turnaround inspection? |
A1–H60RA–MRC–100
|
|
|
Describe the characteristics A/C battery? |
Located in the CO-Pilot Seatwell Nickle–Cadmium24vdc Power |
|
|
For high wind weather conditions, how much deflection of the blade tips is required? |
6–12 inches to prevent damage for overnighting / wind flapping |
|
|
Total Number and Locations of Eye Wash Stations? |
This answer NTB Updated 2 total:Hanger Bay and the Wash Rack Hazmat station |
|
|
Why can't you Check IGB or TGB oil level if the tail is folded?
|
NO!
Because the Aircraft tail is no longer level |
|
|
What are the four things PCs look for during inspections? |
FOD, Intergrity, Security, Corrosion. |
|
|
How long after shutdown can you check APU oil? |
1 hour
|
|
|
Mil spec for hydraulic fluid? |
MIL–PRF–83282
|
|
|
What are the two types of rescue hoist? |
Breeze Eastern & Goodrich
|
|
|
How many people are required for fuel samples? |
3 total:
A fire guard, Safety observer, and the Person taking sample |
|
|
Can you allow personnel to enter/exit while washing #2 engine?
|
yes, stator is engaged, no fuel in engine
|
|
|
What are the power requirements for the A/C?
|
115 VAC, 400 Hertz, 3 Phase
|
|
|
What is the AAR–47?
|
Fish Eye lenses on forward ESM antenna's and tail pylon Warning: inner lens coated with DOUBLE NICKLE SALT danger if leaking!!
|
|
|
How can you spot corrosion on the MGB, TGB, & IGB? |
They're made with Magnesium Alloy, Corrosion will be a White Powdery Mound |
|
|
What are the NATO Codes For Jet Fuel? |
Jet–A1 (F–35) JP–4 (F–40) JP–5 (F–44) JP-8 (F–34) |
|
|
When inspecting the gravity fuel cover what are you looking for?
|
Grounding wire potted, All bolts are present, White arrow facing forward
|
|
|
How long after shutdown can you check engine oil?
|
20 Minutes
|
|
|
Weight of safe fuel load? |
Internal 592 gal – 3988 lbs and External 120 gal – 804 lbs
|
|
|
General responsibility of a Plane Captain? |
Safety, Corrosion Prevention, FOD, Integrity Of A/C, training, and most of all Safety! |
|
|
What Tools are required when checking the servicing levels on the ECS air cycle machine's Oil level? |
Flashlight and Mirror
|
|
|
Where is the Shimmy Damper located? |
Tail Landing Gear Port Side
|
|
|
What does the term Should mean? |
Recommended Action
|
|
|
How long does the BIM indicator take to test if temp is above 20 degrees? |
10–30 seconds
|
|
|
What is directly behind the Title Page? |
IRACS
|
|
|
What does the term "Should" mean? |
A Recommended Action |
|
|
What does "Caution" mean in a pub?
|
Damage or destruction to equipment
|
|
|
What is the Hand Signal Pub? |
NAVAIR 00–80T–113
|
|
|
In heavy weather how many tie downs are required? |
3 at each point for a total of 18 |
|
|
How do you wash a HELO? |
From bottom to top, Inward to outward (prevents streaking)
|
|
|
what does a "Warning" mean in a pub? |
Death or Injury
|
|
|
How often are PC monitors due?
|
Every Six months
|
|
|
What is a BIM? |
Blade Inspecton Method
|
|
|
What does the term "SHALL" mean? |
Mandatory Action
|
|
|
How long do you have to wait to cycle the blade fold motor? |
10 minutes so you don't burn out motor
|
|
|
What is a another name for the "Dog House"? |
Sliding Fairing |
|
|
Can you gravity fuel with engines running? |
No
|
|
|
Where are the tie down points located? |
1 Front tires, 2 between the transition section and the tail, 3 high point located near dog house
|
|
|
What is another name for the doghouse? |
Sliding Fairing |
|
|
What is the difference between the Goodrich and the Breeze eastern Rescue Hoist? |
Breeze Eastern: Has a SpringGoodrich: Has a Rubber Stop Block
|
|
|
What publication is the "Daily Deck"? |
MRC-300
|
|
|
If I needed to preform a Conditional Inspection, What pub would I use? |
MRC-390
|
|
|
In what publication can I find Aircraft Special Inspections? |
MRC-350
|
|
|
The publication for Phase Maintenance is in what pub? |
MRC-400
|
|
|
What does NAMP stand for? |
Naval Aviation Maintenance Program
|
|
|
As a Plane Captain, When preforming a Daily/Turnaround inspection, What are your objectives? |
Safety, Training, and Downing the Aircraft (by the book of course)
|
|
|
What are the minimum qualifications required to safely move and Aircraft? |
Brake Rider, Plane Captain, and a Tow Tractor License
|
|
|
How far below the Full line do you service the engines? |
Approximately one inch from the full line
|
|
|
Do gear boxes consume oil? |
No, they Leak oil
|
|
|
How long should it take for a Pre-Check valve to Stop the flow of fuel? |
With in 5-10 seconds
|
|
|
What is special about the lower third of our fuel cells? |
Contains self sealing compound (Ballistic Gel) Self seals up to 7.62 mm
|
|
|
What is a PDI? |
Pressure Differential Indicator
|
|
|
How many PDI's does the MH-60R contain? |
An MH-60R contains 14 PDI's
|
|
|
What are the locations of the PDI's? |
2 per hydrualic pump (8),
2 per engine (4), 1 on the Pilot Assist mod, and 1 in the cabin on the MGB |
|
|
How many Fire Detectors are on an MH-60R? |
5 total: two per main engines and one on the APU |
|
|
How do you test a Fire Detector? |
With a Flash light equipped with a red lense
|
|
|
At a minimum, what SE licenses are required to be a Plane Captain? |
45 tow tractor, NC-10/108, CC Cart, and light cart
|
|
|
What are the servicing requirements and limitations of the Viscous Damper? |
0-1 inch Good to go, 1-2 inches needs to be serviced, over 2 inches the Viscous Damper needs to be replaced
|
|
|
How do you test a Fire Detector? |
With a Flash light equipped with a red lense |
|
|
When is Hearing Protection Required? |
With in 200 feet of turning aircraft and anything exceeding 85db
|
|
|
What are the three levels of ORM?
|
Time-Critical, Delibrate, and In-Depth
|
|
|
What are the Four Principles of ORM? |
Accept no Unnecessary Risk, Accept Risk only when benefits out weight the cost,
Anticipate and Manage risk, and Make risk decisions at the right level |
|
|
What is an Example of Time Critical ORM? |
A quick mental review of the Five steps
|
|
|
Give an example of Deliberate ORM? |
An Aircraft Move Brief
|
|
|
Give an example of In-Depth ORM? |
Phase Maintenance: Several Steps involving HAZMAT, PPE, Safety, and Tools |
|
|
What is the Military Specification Code for Engine Oil? |
MIL-PRF-23699
|
|
|
What is the Military Specification Code for Hydraulic Fluid? |
MIL-PRF-83282
|
|
|
What is the Military Specification Code for Gear Box Oil? |
DOD-PRF-85734
|
|
|
What is the Alternate Military Specification Code for Engine/Gear Box Oil? |
MIL-PRF-7808
|
|
|
How are you supposed to check for a popped PDI? |
By sliding your finger a crossed the PDI
|
|
|
How many low point fuel drains does an MH -60R aircraft have (w/o AUX tanks)? |
two
|
|
|
Where could you find the Weight of an MH-60R? |
In the Aircraft Weight and Balance (AWAB) section of the Aircraft Discrepancy Logbook (ADB) |
|
|
What is the Main Rotor head diameter? |
644", 53' 8", 16,36m
|
|
|
What is the Tail Rotor diameter? |
132", 11' 0", 3,35m
|
|
|
What is the Span of the Horizontal Stabilator? |
172", 14' 4", 4,37m
|
|
|
What is the Operating Length of the MH-60R? |
778", 64' 10", 19,76m
|
|
|
What is the Operating Height of the MH-60R? |
201", 16' 9", 5,11m
|
|
|
What is the Folded Length of the MH-60R? |
514", 42' 10", 13,04m
|
|
|
What is the Folded Height of the MH-60R? |
159,2", 13' 3,2", 4,04m
|
|
|
What is the Folded Width of the MH-60R? |
132,75", 11' ,75, 3,37m
|
|
|
What is the Length of the MH-60R when the Main Rotor head is folded and the Pylon Flight Length? |
634", 52' 10", 16,18m
|
|
|
|
69', 5' 9", 1,75m |
|
|
What is the Fuselage Length? |
621", 51' 9", 15,76m
|
|
|
What is the weight limitation for an Engine Bay Door? |
1 person or up to 300 lbs
|
|
|
|
69 inches 5' 9" 1.75m |
|
|
To prevent streaking when washing the aircraft, start at the ________ surfaces and work ________ and ________ |
LOWER, UPWARD, OUT
|
|
|
In corrosion, what are the four elements of the "Vicious cycle", and what happens when you remove one of the elements? |
Anode, Cathode, A Continuous liquid / gas Path, and A Metallic path; Corrosion will not occur.
|
|
|
"What general areas of the aircraft are being identified by these buttlines, waterlines, and stations |
Area A: buttline 0, waterline 315, station 343 Area B: buttline 50 R, waterline 240, station 500" A: MAIN ROTOR HEAD B: MAD SYSTEM/SUPPORT (SH-60B) |
|
|
Upon activation of the fuel pre-check valves, flow stoppage should occur within what time? |
5-10 SECONDS
|
|
|
If contaminants are present retain sample, drain approximately 1 gallon into bucket, and take another sample If second sample is contaminated immediately notify whom? |
MAINTENANCE CONTROL
|
|
|
What general areas of the aircraft are being identified by these buttlines, waterlines, and stations: Buttline 0, waterline 315, station 343 |
Main Rotor Head |
|
|
How long is a Daily good for? |
72 HOURS PROVIDED THAT NO FLIGHT OCCURS DURING THIS PERIOD |
MRC-300 |
|
What type of corrosion is described as corrosion that results from the joining of two metals of different electrochemical potential in the presence of an electrolyte |
GALVANIC
|
|
|
(True or False)The aircraft has inoperative brakes; therefore the cockpit shall not be manned Chock walkers will take positions to chock wheels if ordered |
TRUE
|
|
|
What is the shipboard minimum tie down requirement just prior to aircraft movement for the MH-60R |
4 total
|
|
|
Which metal on naval aircraft is the most corrosive |
MAGNESIUM
|
|
|
When folding blades with the APU operating, what potential danger exists |
BLADE FOLD MAY INADVERTENTLY STOP, CAUSING #3 BLADE TO STOP ABOVE THE APU EXHAUST
|
|
|
When servicing the APU oil sump fluid level, the APU should not have been operated for how long |
AT LEAST 1 HOUR
|
|
|
What is the solution that is used during a hot Section Cleaning |
MIL-PRF-85704
|
|
|
Exfoliation is an advanced form of what type of corrosion |
INTERGRANULAR
|
|
|
Who is authorized to remove ordnance from the aircraft |
ONLY PERSONNEL CERTIFIED FOR HANDLING AVIATION ORDNANCE
|
|
|
What cartridge is used on the fire extinguisher on the MH-60R aircraft |
MH92
|
|
|
If the tail pylon or stabilator is folded, ensure that the stab power and ________ circuit breakers are pulled prior to applying external power |
STAB SYSTEM POWER
|
|
|
(True or False) The tail and intermediate gearboxes can be properly checked and serviced with the pylon folded |
FALSE
|
|
|
(True or False) One of the responsibilities of a plane captain is the cleanliness and prevention of corrosion of the aircraft |
TRUE
|
|
|
|
RIGHT FUEL PUMP ACCESS |
|
|
(True or False) When folding the tail rotor pylon, be sure battery/external power is installed and connected for tail rotor index |
TRUE
|
|
|
When directing an aircraft, the plane captain must be ______ feet in front of and ____ feet to the right of the pilot |
50' and 10'
|
|
|
Blade folding and spreading is possible up to what wind velocity |
45 Knots
|
|
|
Following an aborted APU start attempt, you must wait ________ before trying to restart, to allow for ______ |
2 MINUTES; FUEL TO DRAIN
|
|
|
Aircraft ________ is the first step in preventing corrosion |
Cleaning
|
|
|
Upon aircraft shutdown, if a droop stop fails on a blade, the blade could get as close as ______ feet to the ground |
5 Feet
|
|
|
When doing an aircraft wash job, what type of cleaner is used, for light soils, and what is the mixing ratio of soap to water? |
MIL-PRF-85570 TYPE II; 1 TO 9 |
|
|
(True or False) A certified plane captain will be present and supervise all launches and recoveries of aircraft |
TRUE
|
|
|
(True or False) A periodic inspection is required for TD-1A chain assemblies due to constant use and exposure to the elements |
TRUE
|
|
|
What is/are the only approved chocks aboard ship |
NWC-4
|
|
|
At what distance is hearing protection required when the aircraft is turning |
200 Feet
|
|
|
How is the fuel level monitored during gravity fueling |
Visually
|
|
|
You must read the hot side of the -104MGB dipstick within _______ after shutdown |
1/2 to 2 Hours
|
|
|
Where is the shimmy damper located and what is its purpose |
LEFT TAIL WHEEL, AIDS IN ABSORBING TAIL WHEEL OSCILLATIONS
|
|
|
On the hydraulic pumps, what is the acceptable movement of the piston into the overfill zone |
3/8 Inch
|
|
|
Blade folding and spreading is possible up to what wind velocity |
45 Knots
|
|
|
(True or False) Can you gravity fuel with the engines turning |
FALSE
|
|
|
What are the Viscous Damper's air bubble limitations? |
LESS THAN 1 INCH OK, 1-2 INCHES SERVICE, AND OVER 2 SHOULD BE REPLACED |
|
|
What does CATM stand for |
Captive Air Training Missile
|
|
|
What does ALFS stand for |
Airborne Low Frequency Sonar
|
|
|
What is APU accumulator pressure range? |
2700 to 3100 psi. |
|
|
Alternate for Engine Oil and Gear Box Oil |
MIL-PRF-7808 |
|
|
What three people sign the A-Sheet?
|
The Inspecting PC Safe For Flight Pilot |
|
|
What are you saying when you sign the A-Sheet?
|
I have personally inspected this aircraft IAW the applicable MRCs/checklists. Any discrepancies noted have been entered on a work order. |
|
|
What is the only servicing checked on a Daily Inspection?
|
Air Cycle Machine in the ECS compartment. |
MRC-350 Card 22.2 Step 2.9
|
|
What do you need to properly check the servicing on the Air Cycle Machine?
|
A flash light and a mirror.
|
|
|
What are you saying when you sign the A Sheet? |
I have personally inspected this aircraft IAW all applicable publications Any discrepancies found have been documented on a MAF. |
|
|
What is the red mark for on the tail tires? |
It is a Slip Mark used to determine how far the tire has slipped on the rim. |
|
|
What is the Slip Mark limitation on the tail tires? |
1/4 inch. Any more than that could result in the valve stem to be sheared off. |
|