Kirby's Ndi Ures Vol. 1

Front 1

Technical orders provide all of the following pertaining to the inspection, operation, maintenance, and modification of Air Force equipment and material except:

Back 1

Policy Directives

Front 2

Simply stated, a technical order is considered to be:

Back 2

a military order

Front 3

Technical Orders are established, numbered, and issued in accordance with which TO?

Back 3

00-5-1

Front 4

Which type of TO covers installation, troubleshooting, repairing, removing, calibration, and servicing or handling of Air Force military systems?

Back 4

Operations and maintenance TOs

Front 5

ETIMS provides a direct on-line connectivity from every base into the management system to allow all except:

Back 5

most current publication date

Front 6

To find the most current publication date of a TO, check

Back 6

the TO index

Front 7

MIDAS is:

Back 7

a six digit numbering system expressed as three elements of two digits each

Front 8

What information does the NDI general system (GS) manual provide?

Back 8

Inspections

Front 9

What type of vehicle equipment manual would contain calibration requirements?

Back 9

Operation and service manual

Front 10

A group assembly parts list has several part numbers listed for a part you need. To determine which part number is right for your aircraft, refer to the

Back 10

useable on code condition

Front 11

Where would you find information for recording and reporting a nondestructive inspection (NDI) technique to inspect an F-16C speed brake?

Back 11

TO 33B-1-1

Front 12

You are tasked to do an inspection; however you only know the name of the part you are to inspect. To locate the applicable paragraph and figure number for the inspection, check the TO's

Back 12

alphabetical index

Front 13

While doing a job you find a mistake in a TO. Correcting this requires initiation of a Technical Manual Change Recommendation and Reply form. Who is responsible for this action?

Back 13

You

Front 14

Which change recommendation priority must be answered within 40 calender days?

Back 14

Urgent

Front 15

Which type change recommendation priority is used to recommend improvements to correct potential hazards?

Back 15

Routine

Front 16

Which technical order (TO) contains complete instructions for maintaining TOs?

Back 16

00-5-1

Front 17

Electronic Technical orders (TO) are files identified by a media distribution code suffix of

Back 17

-WA-n

Front 18

You need to order a new technical order (TO) for personnel use on a regular basis; how would you accomplish this action?

Back 18

Establish an ID requirement

Front 19

The technical order (TO) listing for your shop's operational TO file will show you all of the following except

Back 19

who currently has one signed out

Front 20

Responsibility for consolidating technical order (TO) requests on an installation rests with the

Back 20

personnel in the TODO

Front 21

With few exceptions, you must file technical orders (TO) within a maximum of

Back 21

five work days of receipt

Front 22

A technical order (TO) effective date is

Back 22

later than the basic date

Front 23

In which technical order (TO) chapter would you find page 4-2?

Back 23

4

Front 24

File technical order (TO) supplements in

Back 24

reverse numerical order in front of the basic TO

Front 25

ETIMS will be updated automatically in no more than how many days?

Back 25

7 calendar days

Front 26

Who has ownership of Air Force supplies and equipment?

Back 26

American taxpayer

Front 27

The purpose of the Air Force supply system is to

Back 27

provide a means of purchasing, distributing, and controlling equipment/supplies used by the Air Force

Front 28

Which system is used to determine whether your NDI laboratory is authorized a piece if equipment?

Back 28

AFEMS

Front 29

Which form is used to request an item not listed in the Federal Supply System?

Back 29

DD Form 1348-6

Front 30

Which condition tag would be placed on an eddy current unit sent back to depot for repair?

Back 30

Green DD Form 1577-2

Front 31

All of these are requirements for an initial journeyman skill level except you must

Back 31

complete 9 months of on-the-job training

Front 32

From the lowest to the highest , what are the three levels of maintenance capability?

Back 32

Organizational, intermediate, depot

Front 33

Which level of maintenance involves major repairs and overhaul?

Back 33

Depot

Front 34

Which inspection involves a thorough and searching review of an entire weapon system?

Back 34

Periodic (PE)

Front 35

Which inspection attempts to minimize the length of time an aircraft is down for inspection?

Back 35

Phase (PH)

Front 36

Which inspection is based on calendar days?

Back 36

Isochronal (ISO)

Front 37

Which maintenance symbol would be used to indicate a scheduled periodic (PE) inspection is overdue?

Back 37

Red Dash

Front 38

Which symbol signifies that an unsatisfactory condition exists?

Back 38

Red Diagonal

Front 39

Category I deficiency reports (DR) are not used to report conditions

Back 39

resulting from nonconformance to specifications

Front 40

Maintenance data documentation (MDD) is grouped into what categories?

Back 40

On- and off-equipment

Front 41

You would not find maintenance data documentation (MDD) rules in

Back 41

TO 00-35D-54

Front 42

Maintenance information system (MIS) refers to an automated maintenance information system that supports and enables what?

Back 42

Maintenance business procedures

Front 43

Which maintenance data documentation code (MDD) codes to simplify reporting?

Back 43

How malfunctioned

Front 44

Which is NOT a maintenance inspector function?

Back 44

Verify the quantity of modified parts is correct

Front 45

All engine flight data can be found on Air Force Technical Order (AFTO) Form

Back 45

781J

Front 46

What is the correct format for entering a date in the 781 series forms?

Back 46

YYYYMMDD

Front 47

Which blocks are used by nondestructive inspection (NDI) personnel to clear all red dash discrepencies?

Back 47

Inspected by and employee no. blocks

Front 48

What is used to record service, periodic, and special inspections, and the current status of equipment?

Back 48

AFTO 244

Front 49

What indicates a special inspection or operational check is due, a scheduled inspection is overdue, and the equipment is in an unknown condition?

Back 49

A red dash

Front 50

What is a database developed for the NDI career field in an effort to reduce paper and improve the management of process controls and equipment maintenace?

Back 50

PCAMS

Front 51

What are commanders, staff officers, and supervisors responsible for when it comes to accident prevention?

Back 51

Standards and regulations

Front 52

The MINIMUM temperature required for a substance to initiate self-sustained combustion is the

Back 52

ignition temperature

Front 53

The danger from static electricity is highest during

Back 53

cold, dry weather

Front 54

All of these have the potential for serious injury, when wearing jewelry EXCEPT

Back 54

wearing gloves on the hand to prevent injury

Front 55

Which personnel protective equipment is not normally used in the nondestructive inspection process?

Back 55

Long sleeves

Front 56

Unattended parked vehicles on the flightline must

Back 56

have keys left in the ignition

Front 57

Engine position numbers on multi-engine aircraft are assigned consecutively from the

Back 57

tip of the left wing to the tip of the right wing

Front 58

Where is am aircraft elevator located?

Back 58

On the empennage

Front 59

The tie-down rings on aerospace ground equipment (AGE) are normally attached to the

Back 59

frame

Front 60

Areospace ground equipment (AGE) power system components are NOT made from

Back 60

copper

Front 61

How are permanent joints on Areospace ground equipment (AGE) enclosures normally attached?

Back 61

Riveted

Front 62

How many standard markings are applied to all Air Force aircraft?

Back 62

Six

Front 63

Where are station numbers located on fixed wing aircraft?

Back 63

Nose

Front 64

Which is NOT an aircraft identification and safety marking?

Back 64

Crew

Front 65

What symbol is used to indicate an installed ejection system?

Back 65

Triangle with apex pointed down

Front 66

What small and subdued safety marking alerts you to a hazardous condition?

Back 66

Warning text

Front 67

Depending on the type of aircraft and engine, how big is the noise safety zone circle surrounding the airflcraft?

Back 67

300 to 400 feet