Use LEFT and RIGHT arrow keys to navigate between flashcards;
Use UP and DOWN arrow keys to flip the card;
H to show hint;
A reads text to speech;
13 Cards in this Set
- Front
- Back
|
Relative to boilers and pressure vessels, a code that has not been adopted by all the provinces is: A) CSA B52 B) ANSI B.31.5 C) NFPA D) ASME I through IX E) CSA B51
|
C) NFPA |
|
|
A body which was formed in 1919 for the promotion of safety and uniformity in the construction, installation and inspection of boilers and pressure vessels was the: A) ASME B) CSA C) Underwriter Laboratories Canada D) NFPA E) National Board of Boiler and Pressure Vessel Inspectors
|
E) National Board of Boiler and Pressure Vessel Inspectors |
|
|
The code that regulates mechanical refrigeration is the: A) ASME Section IV B) CSA B-52 C) ASME Section I D) CSA B-51 E) ASME Section VII
|
B) CSA B-52 |
|
|
The first Canadian province to enact boiler and pressure vessel legislation was: A) Ontario B) Alberta C) Newfoundland D) Manitoba E) Quebec
|
E) Quebec |
|
|
Heating boiler means a boiler: A) Where water is heated to a pressure exceeding 1 100 kPa and a temperature of 121ºC B) Which does not require a sight glass C) Where steam is produced at a pressure greater than 103 kPa D) Where steam is produced at a pressure of 103 kPa or less E) In which only hot water is produced
|
D) Where steam is produced at a pressure of 103 kPa or less |
|
|
Once you have taken over a shift in a high pressure boiler plant, you may leave the boiler unattended for: A) No period of time B) The time specified in the union agreement C) 4 hours D) 40 minutes E) 15 minute intervals
|
A) No period of time |
|
|
When calculations are made with respect to the application of the Boilers Act, 10 kilowatts is equal to: A) 1 m² of heating surface B) 0.5 m² of heating surface C) 2 m² of heating surface D) 5 m² of heating surface E) 10 m² of heating surface
|
A) 1 m² of heating surface |
|
|
After an initial inspection of a boiler or pressure vessel, an Alberta identification number preceded by the letter "A" in a/an _____ shall be stamped on the boiler or pressure vessel. A) Circle B) Rectangle C) Square D) Octagon E) Hexagon
|
A) Circle |
|
|
A fitting, as defined in the "Act", means a: A) Fan B) Pump C) Stack D) Gauge glass E) Feedwater regulator
|
D) Gauge glass |
|
|
The Act and Regulations do not apply to a: A) Power plant having a boiler rating of 10 kW or less B) Heating plant having a rating of 25 kW or more C) Heating plant having a boiler rating of 20 kW or more D) Heating plant having a boiler rating of 30 kW or less E) Power plant having a boiler rating of 20 kW or less
|
A) Power plant having a boiler rating of 10 kW or less |
|
|
The Province of Alberta currently has various certificates of competency relative to Power Engineering and Boiler Operation, the number being: A) 12 B) 6 C) 4 D) 8 E) 10 |
E) 10 |
|
|
A Fourth Class Engineer's Certificate of Competency qualifies the holder to take charge of a Power Plant not exceeding: A) 1 000 kW B) 500 kW C) 2 500 kW D) 5 000 kW E) 100 kW |
A) 1 000 kW |
|
|
Definitions such as shift engineer, chief engineer and fireman are found in: A) Alberta's Safety Codes Act B) Alberta Engineers' Regulations C) Municipal codes D) CSA B-51 E) ASME Code Section VIII
|
B) Alberta Engineers' Regulations |
